o.k proftp kann ich schon mal im webmin sehen aber immer noch nicht starten
habe ein start script in /etc/init.d mit namen proftpd und die schaut so aus!
aber starten tut er den ftp nicht(fehlermeldung unten)
#! /bin/sh
# $local_fs all local file systems are mounted
# (most services should need this!)
# $remote_fs all remote file systems are mounted
# (note that /usr may be remote, so
# many services should Require this!)
# $syslog system logging facility up
# $network low level networking (eth card, ...)
# $named hostname resolution available
# $netdaemons all network daemons are running
# Check for missing binaries (stale symlinks should not happen)
PROFTPD_BIN=/usr/local/sbin/proftpd
test -x $PROFTPD_BIN || exit 5
# Check for existence of needed config file and read it
PROFTPD_CONFIG=/usr/local/etc/proftpd.conf
test -r $PROFTPD_CONFIG || exit 6
# . $PROFTPD_CONFIG
. /etc/rc.status
# Reset status of this service
rc_reset
case "$1" in
start)
echo -n "Starting ProFTPD "
## Start daemon with startproc(
. If this fails
## the return value is set appropriately by startproc.
startproc $PROFTPD_BIN
# Remember status and be verbose
rc_status -v
;;
stop)
echo -n "Shutting down ProFTPD "
## Stop daemon with killproc(
and if this fails
## killproc sets the return value according to LSB.
killproc -TERM $PROFTPD_BIN
# Remember status and be verbose
rc_status -v
;;
try-restart)
## Do a restart only if the service was active before.
## Note: try-restart is not (yet) part of LSB (as of 1.2)
$0 status >/dev/null && $0 restart
# Remember status and be quiet
rc_status
;;
restart)
## Stop the service and regardless of whether it was
## running or not, start it again.
$0 stop
$0 start
# Remember status and be quiet
rc_status
;;
force-reload)
## Signal the daemon to reload its config. Most daemons
## do this on signal 1 (SIGHUP).
## If it does not support it, restart.
echo -n "Reload service ProFTPD "
## if it supports it:
killproc -HUP $PROFTPD_BIN
#touch /var/run/FOO.pid
rc_status -v
## Otherwise:
#$0 stop && $0 start
#rc_status
;;
reload)
## Like force-reload, but if daemon does not support
## signaling, do nothing (!)
# If it supports signaling:
echo -n "Reload service PROFTPD "
killproc -HUP $PROFTPD_BIN
#touch /var/run/FOO.pid
rc_status -v
## Otherwise if it does not support reload:
#rc_failed 3
#rc_status -v
;;
status)
echo -n "Checking for service ProFTPD "
## Check status with checkproc(
, if process is running
## checkproc will return with exit status 0.
checkproc $PROFTPD_BIN
# NOTE: rc_status knows that we called this init script with
# "status" option and adapts its messages accordingly.
rc_status -v
;;
probe)
## Optional: Probe for the necessity of a reload, print out the
## argument to this init script which is required for a reload.
## Note: probe is not (yet) part of LSB (as of 1.2)
# test /etc/FOO/FOO.conf -nt /var/run/FOO.pid && echo reload
;;
*)
echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload|probe}"
exit 1
;;
esac
rc_exit
fehlermeldung:
/etc/init.d/proftpd: line 1: ---8: No such file or directory
: command not found: line 3:
: command not found: line 13:
: command not found: line 14:
: numeric argument required7: exit: 5
was kann es sein plz help
