Start Script
Da Dein Start Script vollstaendig anders aussieht als mein, poste ich Dir mal meins. Ich habe SuSE 8.2 am laufen, ProFTPD aus dem Tarball selber kompiliert, ohne irgendwie was an den Dirs zu machen. Sollte also identisch wie bei Dir sein:
---------------------
linux:/home/stonki/000/proftpd-1.2.8/contrib # less /etc/init.d/proftpd
#! /bin/sh
### BEGIN INIT INFO
# Provides: ProFTPD
# Required-Start: $syslog $network
# X-UnitedLinux-Should-Start:
# Required-Stop: $syslog $network
# X-UnitedLinux-Should-Stop:
# Default-Start: 3 5
# Default-Stop: 0 1 2 6
# Short-Description: ProFTPD
# Description: Start ProFTPD to allow FTP Services
#! /bin/sh
# $local_fs all local file systems are mounted
# (most services should need this!)
# $remote_fs all remote file systems are mounted
# (note that /usr may be remote, so
# many services should Require this!)
# $syslog system logging facility up
# $network low level networking (eth card, ...)
# $named hostname resolution available
# $netdaemons all network daemons are running
# Check for missing binaries (stale symlinks should not happen)
PROFTPD_BIN=/usr/local/sbin/proftpd
test -x $PROFTPD_BIN || exit 5
# Check for existence of needed config file and read it
PROFTPD_CONFIG=/usr/local/etc/proftpd.conf
test -r $PROFTPD_CONFIG || exit 6
# . $PROFTPD_CONFIG
. /etc/rc.status
# Reset status of this service
rc_reset
case "$1" in
start)
echo -n "Starting ProFTPD "
## Start daemon with startproc(8). If this fails
## the return value is set appropriately by startproc.
startproc $PROFTPD_BIN
# Remember status and be verbose
rc_status -v
;;
stop)
echo -n "Shutting down ProFTPD "
## Stop daemon with killproc(8) and if this fails
## killproc sets the return value according to LSB.
killproc -TERM $PROFTPD_BIN
# Remember status and be verbose
rc_status -v
;;
try-restart)
## Do a restart only if the service was active before.
## Note: try-restart is not (yet) part of LSB (as of 1.2)
$0 status >/dev/null && $0 restart
# Remember status and be quiet
rc_status
;;
restart)
## Stop the service and regardless of whether it was
## running or not, start it again.
$0 stop
$0 start
# Remember status and be quiet
rc_status
;;
force-reload)
## Signal the daemon to reload its config. Most daemons
## do this on signal 1 (SIGHUP).
## If it does not support it, restart.
echo -n "Reload service ProFTPD "
## if it supports it:
killproc -HUP $PROFTPD_BIN
#touch /var/run/FOO.pid
rc_status -v
## Otherwise:
#$0 stop && $0 start
#rc_status
;;
reload)
## Like force-reload, but if daemon does not support
## signaling, do nothing (!)
# If it supports signaling:
echo -n "Reload service PROFTPD "
killproc -HUP $PROFTPD_BIN
#touch /var/run/FOO.pid
rc_status -v
## Otherwise if it does not support reload:
#rc_failed 3
#rc_status -v
;;
status)
echo -n "Checking for service ProFTPD "
## Check status with checkproc(8), if process is running
## checkproc will return with exit status 0.
checkproc $PROFTPD_BIN
# NOTE: rc_status knows that we called this init script with
# "status" option and adapts its messages accordingly.
rc_status -v
;;
probe)
## Optional: Probe for the necessity of a reload, print out the
## argument to this init script which is required for a reload.
## Note: probe is not (yet) part of LSB (as of 1.2)
# test /etc/FOO/FOO.conf -nt /var/run/FOO.pid && echo reload
;;
*)
echo "Usage: $0 {start|stop|status|try-restart|restart|force-reload|reload|probe}"
exit 1
;;
esac
rc_exit
--------------------------------------------------------------------------
Zeige Beiträge
RTFM 
